- ELECTRICAL PRODUCT
- FIXED GAS AND FLAME DETECTION SOLUTIONS
- GAS PRODUCT
- CONTRIVE BURNER CONTROL DEVICE
- DUNGS GAS COMPONENTS
- ACCESSORIES
- BALL VALVE
- BURNER MANAGEMENT SYSTEMS AUTOMATIC BURNER CONTROLS
- DOUBLE SOLENOID VALVES
- ELECTRO PNEUMATIC VALVES
- FILTER
- GASMULTIBLOC® MULTIFUNCTIONAL GAS CONTROLS
- MOTOR BUTTERFLY VALVES AND ACTUATORS
- PRESSURE REGULATORS
- PRESSURE SWITCHES FOR GAS AND AIR
- SOLENOID VALVES
- SYSTEM ENGINEERING GAS TRAINS - DUNGSHeatEngine
- VALVE PROVING SYSTEMS LINE LEAKAGE TESTERS-LABORATORY - KITCHEN
- View All
- ECLIPSE BURNER PARTS
- ECONEX GAS TRAIN PRODUCT
- ACCESSORIES FOR GEAR MOTORS
- AIR AND GAS BUTTERFLY VALVE
- DIAL PRESSURE GAUGE
- ELECTRIC ACTUATORS
- ENGINEERED GAS SKID & VALVE TRAIN - GAS PRESSURE REDUCTION STATION
- FLAME SUPERVISION - BURNER CONTROL
- FLAME SUPERVISION - UV DETECTION
- GAS BALL VALVE
- GAS FILTER SERIES (FE)
- GAS PRESSURE REGULATOR
- GAS PRESSURE SWITCH
- GAS SOLENOID & SHUT OFF VALVE
- LINEAR CONTROL VALVE SERIES (MPV)
- MODULATING CONTROL VALVE SERIES (MDV-B1..., B1... E)
- MODULATING CONTROL VALVE SERIES (MDV-D1)
- MOTORIZED BUTTERFLY VALVES ELECTRONIC OR PNEUMATIC ACTUATOR
- NEEDLE VALVE
- PACKAGED VALVE TRAINS - GAS SOLENOID & SHUT OFF VALVE
- SAFETY RELIEF VALVE
- SOLENOID BUTTERFLY VALVE SERIES (BFVS)
- TURBINE METER
- TWO-WAY MANUAL PRESSURE COCK WITH BLEED-OFF
- VALVE PROVING SYSTEM
- View All
- ENOLGAS BONOMI VALVE & ACTUATOR
- GAS BURNER COMTHERM UK
- AIR HEATER (AHP)
- AIR HEATER (HEF)
- AIR HEATER (HEM)
- AIR HEATER (HET)
- COMTHERM EK BURNER
- COMTHERM PROCESS CONE (PC) BURNER
- COMTHERM PROCESS PAK (PP) BURNER
- COMTHERM RECIRCULATION SIDE-PLATE (RSP) BURNER
- COMTHERM SIDE-PLATE (SP) BURNER
- COMTHERM TF IMMERSION BURNER
- COMTHERM TFR IMMERSION BURNER
- DIRECT FIRED AIR HEATER
- FUME INCINERATION BURNER
- PROCESS - HEAT NORMAL CAPACITY (PH)
- PROCESS - HEAT NORMAL CAPACITY (PHC)
- View All
- GAS BURNER SANTIN ITALY
- GAS BURNER SELAS USA
- GECA GAS TRAIN EQUIPMENT
- HONEYWELL
- MAXON BURNER PARTS
- MEDENUS GAS TRAIN PRODUCT
- MTI GAS DETECTOR
- POLIX VALVE
- SIEMENS BURNER PARTS
- YETEN COMBUSTION
- View All
- MECHANICAL PRODUCT
- PROCESS MEASUREMENT AND CONTROL
- THERMOPLASTIC SOLUTIONS
- STUEBBE AERATION & VENT VALVES
- STUEBBE BALL VALVES
- STUEBBE BUTTERFLY VALVES
- STUEBBE CHEMICAL PUMP
- STUEBBE DIAPHRAGM VALVES
- STUEBBE DISPLAY AND CONTROL UNIT
- STUEBBE LEVEL MEASUREMENT
- STUEBBE LIQUID FLOWMETERS
- STUEBBE PRESSURE REDUCING VALVES
- STUEBBE PRESSURE RELIEF VALVES
- STUEBBE PRESSURE SENSOR
- STUEBBE WATER JET PUMP
- View All
PYRONICS - SINGLE-ENDED RECUPERATIVE RADIANT TUBE COMBUSTION SYSTEM(SER)OR (UHF)
|
PYRONICS - SINGLE-ENDED RECUPERATIVE RADIANT TUBE COMBUSTION SYSTEM(SER)OR (UHF) |
Single-ended Recuperative Radiant Tube Combustion System
Radiant tube burners are recuperative style and available as single end (SER) or direct fired (UHF).
In a furnace operating with a conventional radiant tube combustion system, 65 to 70% of the heat created by combustion is wasted in the ue gas.
Single-ended recuperative radiant tube combustion system (SER) reduces that wasted heat dramatically. Because it uses up to 70% of the available exhaust gas heat to preheat incoming combustion air the furnace’s fuel consumption is reduced signicantly (Fig. 1).
The result is average fuel savings of up to 50%. The patented SER is a complete system, combining burner, radiant tube and recuperator in a single, compact unit. It comes with all the accessories needed, from adjustable gas cocks to buttery valves to ignition system (Fig. 1).
Fig. 1. As the incoming combustion air passes through the SER’s recuperator section, it is preheated by hot exhaust gases. The medium velocity, sealed nozzle mix burner utilizes both gas and preheated air and fires down a center flame tube to provide uniform progressive combustion.
Because existing hardware and applications vary from facility to facility, every SER is custom engineered to maximize combustion efficiency.
SER users typically experience fuel savings of 40 to 50%.
Fig. 2. To determine the fuel savings expected, draw a straight line from flue gas temperature to post-conversion preheat temperature. For example, air preheated to 1200 degrees F from 1900 degrees F flue gas will result in fuel savings of about 37-1/2%.
Every SER component is designed to give many years of reliable service. Materials are carefully evaluated to assure component life consistent with the application – generally speaking, FeNiCr or FeCrNi in either a cast or wrought form are used.
These materials are fabricated or formed into components engineered for extended reliability.
For example, the SER’s medium velocity burner provides delayed mixing and uniform progressive combustion, for even tube heating and temperature uniformity.
Its innovative spark system delivers consistently troublefree ignition.
Features like these result in reliable performance, year after year. The proof is in the field: thousands of SER’s are already providing dependable service in captive and commercial heat treat shops around the world.
Because SER’s are easy to install and service, they reduce conversion downtime to a minimum.
Installation is simply a matter of removing existing tubes and burners and re-piping the main gas and air supplies to the SER. Even for untrained personnel, it takes as little as four man-hours per tube.
Servicing an SER is simple. The precisely sized and integrated components provide for easy adjustment of gas/air ratios.
All of which means furnace efficiency can be maximized with virtually no sacrifice in productivity.
Max. air pressure required 1.75” W. C.
Max. gas pressure required 1” W. C.
*Dissipation rate is based upon theoretical calculation considering no specific environment.
NOTE : All dimensions in inches ± 1/8
Ordering Information
Contact factory for assistance.
Download Files
- Brochure_Single-ended_Recuperative.pdf (651.88 KB)